How To Fix Fisher Paykel Washing Machine

Asked by: Abubacar Basch

asked in category: General Last Updated: 22nd May, 2020

Is there a reset button on a Fisher and Paykel washing machine?

Factory Reset

Turn the dial to select 'Spin'. Touch and hold the 'Delay Start' 'More' , the 'Delay Start' 'Less' and 'Options' buttons together for 3 seconds will appear on the screen and the machine will beep. Your washer will now be reset to the default settings.

How to Troubleshoot Fisher Paykel Washers

Check the hot water light.
Check the cold water light.
Check both the hot and cold water lights.
Check the high water light.
Look at the first rinse light and spin light.
Examine the lid-lock light.
Look at the first rinse light, the spin light and the spin speed light.

Subsequently, question is, how do you run a diagnostic on a Fisher Paykel washing machine? Turn the power on at the power point but off at the machine. Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up. Release buttons when the beeps indicate diagnostic mode has been entered. The SmartDrive is now in diagnostic mode.

People also ask, why is my washing machine not turning on?

The lid switch is under the lid. If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad. To test the switch, turn off power to washer and remove the wires from the lid switch.

How do I reset my washing machine?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a "reset" signal to all the components.

25 Related Question Answers Found

Why is the washing machine not working?

If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken.

How do you diagnose a washing machine?

Remove the power source to the washer before troubleshooting or attempting repairs. #1 - Washer Won't Turn On. #2 - Not Draining Properly. #3 - Will Not Spin and/or Agitate. #4 - Washer Leaking Water. #5 - Does Not Dispense Detergent. #6 - Washer is Shaking and Moving. #7 - Washer is Noisy. #8 - Washer Smells.

Why does my washing machine not spin all the water out?

If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Test to be sure the drain pump is working properly.

How do you reset a front load washer?

How to reset the washing machine: Press POWER to turn the washer off. Unplug the washer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the START/PAUSE button for 5 seconds. Plug the washer back in, or turn the circuit breaker back on.

How do I reset my Smart Drive washing machine?

How to Reset a Smart Drive Fisher & Paykel 608 Go to the electrical outlet that you have your Fisher & Paykel Smart Drive washer plugged into. Ensure that you are not in the middle of a washing cycle. Unplug the electrical cord from the wall outlet and wait 30 seconds. Plug the electrical cord back into the wall and turn the Smart Drive back on.

Why is the washing machine beeping?

Washer sounds and beeps Your machine is checking that the water has drained before spinning. Your washer will beep if you have used 'No Spin' and at the end of the cycle. If your machine is beeping continuously or giving a musical series of beeps, refer to the 'Before you call for service' section.

How do I reset my Fisher and Paykel Washsmart?

You can reset your washer to the settings it left the factory with: Enter Option Adjustment mode (refer to 'Option Adjustment'). Select the 'Delicate' cycle. The display will show . Touch and hold for 3 seconds to reset your washer to its factory settings.

How do I reset my Fisher and Paykel dryer?

You can reset your dryer to the default settings it left the factory with: Press and hold the 'Keylock' and 'Delicate' buttons together for three seconds. Your dryer will now be reset to the default settings.

How do you take apart a Fisher and Paykel washing machine?

How to disassemble Fisher and Paykel smartdrive electronic washing machine Isolate from the power supply. To remove the lid, open it to the upright position and lift it clear. Remove the 2 screws from the rear of the top console, disconnect the earth lead. Disconnect the pressure tube from the pressure sensor.